AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Pixel clock rainmeter skin4/2/2024 If set to 1, the skin will snap onto screen edges and other skins when moved. If set to 1, the skin can be dragged around with the mouse. Using Stay Topmost can overcome this, but again, you must not have two skins set to Stay Topmost that overlap. Note: If another application window explicitly sets itself to "top" after a skin set to Topmost is loaded, the application window will be in front until the skin is clicked or refreshed. Overlapping skins with the same setting should use LoadOrder to control relative position. Two Rainmeter skins both set to On Desktop will not change relative to each other on click. ![]() The skin will stay visible when showing the desktop and stay behind other normal application windows. AlwaysOnTop Default: 0ĭefines the Z-position (front to back) of the skin. If set to 1, changes to the window position will be saved to Rainmeter.ini. The value is in pixels.Ī trailing % sign indicates that the value is a percentage of the config window width, rather than pixels.Ī trailing R with AnchorX will make the position relative to the right edge of the config window instead of the left.Ī trailing B with AnchorY will make the position relative to the bottom edge of the config window instead of the top.īoth AnchorX and AnchorY will accept formulas.Īs an example, by setting WindowX, WindowY, AnchorX and AnchorY all to 50% the config will be truly centered in the primary monitor regardless of screen resolution or aspect ratio. AnchorX and AnchorY allow that anchor position to be changed. The screen selection will apply to both WindowX and WindowY if the value is set on only one of AnchorX, AnchorYīy default WindowX and WindowY control the position of the upper left corner of the config window. You can override this with N where N is 0 to 32 and denotes which screen to position the skin on (1-32) or the virtual desktop (0). The formula must be enclosed in (parenthese), with any trailing % / R / B at the end, and outside the (parentheses).īy default the position is relative to the primary screen. The % and R / B modifiers can be used together.īoth WindowX and WindowY will accept formulas. The value is in pixels.Ī trailing % sign indicates that the value is a percentage of the screen width, rather than pixels.Ī trailing R with WindowX will make the position relative to the right edge of the screen instead of the left.Ī trailing B with WindowY will make the position relative to the bottom edge of the screen instead of the top. ini or variant is the file in alphabetical order in the config folder. If a number other than 0, the active skin. The skin is defined in Rainmeter.ini using the Config name. ) define options for how the skin is loaded and displayed in Rainmeter. In balala's code above, using TransformationMatrix=1 0 (tan(rad(-15))) -1 (0.82**tan(rad(15))) (2*0.82*) gives more or less the same result, give or take 1 pixel horizontally.Skin sections in Rainmeter.ini (e.g. the sum between the up bearing and the actual character bounding box). Unfortunately, due to the fact that the side bearings (aka font glypth paddings) around characters are font dependant, there is no easy way to calculate such a value (e.g. It's the opposite skew angle because the vertical flip changes the sign of the angle, and if you move the skin in your top left corner of your screen, take a screenshot and measure the distance from the top of the image (or skin, in this case) to where the original digits end, you'll notice that 144 is precisely that height / offset. I believe it's simply the tangent of the opposite skew angle multiplied with the vertical offset, the math seems to check out.įor example, in your code, if you use TransformationMatrix=1 0 (tan(rad(-15))) -1 (tan(rad(15))*144) 290 it produces the correct result. SilverAzide wrote: ↑ March 16th, 2023, 9:01 pmI don't know the trick to moving the flipped text to offset the 15 degree tilt without hardcoding the offset value. ![]() However this is also possible, if needed. No scrolling or other way to set the size on the flight. ![]() Finally added the DynamicVariables=1 option to the same meter.įor now the setting of size can be done only manually.Added an InlineSetting option to the meter.Added the fontSize variable into the section.Added the BackgroundMode and SolidColor options to the section (to make the skin easier clickable).I altered and added the following options: Set the last value to position this string at the bottom of the upright time: Set the alpha value to 100 so it looks pale Set this to prevent clipping of the time at the bottom
0 Comments
Read More
Leave a Reply. |